济南彩钢板

10年品牌值得信赖
精诚团结、奋起拼搏、开拓进取

济南彩钢板

13969159292

0531-88686388

新闻中心

首页>>新闻中心>>彩钢复合板的表皮形成原理介绍
新闻中心
联系我们
济南坚固彩钢工程公司

联系人:

电话:13969159292

地址:济南市工业北路81号北邻

彩钢复合板的表皮形成原理介绍

来源:http://www.jnjgcg.com/ 日期:2021-01-19 发布人:jiangucaigang
彩钢复合板在形成的时候是有一定的流程的,那么了解该产品的表皮形成原理是很有必要了解一下的,以方便在制备的时候用到。
There is a certain process in the formation of color steel composite plate, so it is necessary to understand the skin formation principle of the product, so as to facilitate the use in the preparation.
整皮彩钢复合板的外皮与芯层在一次成型过程中同时制得,也就是表皮与芯层都由相同的材料制成。产品表皮的形成,主要是受到模具温度和模腔内压力相互作用的结果。
The outer skin and the core of the whole skin color steel composite plate are made at the same time in one molding process, that is, the outer skin and the core are made of the same material. The formation of product skin is mainly affected by the interaction of mold temperature and mold cavity pressure.
济南复合板厂
 
多元醇A组分及异氰酸B组分按配比充分混合后进人模具进行化学反应,反应放出的热量使混合物中的发泡剂气化,这样在整个反应体系中存在着液相和气相。
Polyol a component and isocyanate B component are fully mixed according to the proportion before entering the mold for chemical reaction. The heat released by the reaction makes the foaming agent in the mixture gasify, so there are liquid and gas phases in the whole reaction system.
热力学研究表明,表皮的形成主要受模具温度和模塑压力影响,压力和温度能导致正在反应的混合物中液体和气体的动态平衡。反应体系中靠近模具表面温度低,使得这种平衡有利于产生液态|而在模具的部位温度大多高于100℃,有利于形成气态。
Thermodynamic studies show that the formation of skin is mainly affected by mold temperature and molding pressure, which can lead to the dynamic equilibrium of liquid and gas in the reaction mixture. In the reaction system, the temperature near the surface of the mold is low, which makes the equilibrium conducive to the formation of liquid | and the temperature in the center of the mold is mostly higher than 100 ℃, which is conducive to the formation of gas state.
彩钢复合板靠近模具表面的物料,由于热量被模具吸收一部分,同时由于发泡产生的压力,而使气化物(发泡剂)溶于PU中,形成的气泡发生破裂,高温的芯层物料在模具的表面被压制成结实的表皮,直至放出和吸收的热量平衡为止。
The material close to the die surface of color steel clad plate is partly absorbed by the die due to heat. At the same time, due to the pressure generated by foaming, the vaporizer (foaming agent) is dissolved in Pu, and the bubble formed is broken. The high temperature core material is pressed into a solid skin on the die surface until the heat released and absorbed is balanced.
此文关键词: 济南彩钢复合板厂  

推荐阅读/ Recommended reading

 据统计,现代仓库顶层一般采用彩钢板建造,这种建筑材料近年来在东南亚等国家十分流行,其功能特点逐渐被世界各国所认可。  According

济南彩钢瓦的安装焊接程序 2021-03-02
济南彩钢板的防火注意事项分享! 2021-02-25
C型钢进行脱脂有几种方法? 2021-02-23
济南彩钢板房用料介绍 2021-02-20