济南彩钢板

10年品牌值得信赖
精诚团结、奋起拼搏、开拓进取

济南彩钢板

13969159292

0531-88686388

新闻中心

首页>>新闻中心>>怎么样使用岩棉复合板进行房屋的隔断处理?
新闻中心
联系我们
济南坚固彩钢工程公司

联系人:

电话:13969159292

地址:济南市工业北路81号北邻

怎么样使用岩棉复合板进行房屋的隔断处理?

来源:http://www.jnjgcg.com/ 日期:2021-10-09 发布人:jiangucaigang
岩棉复合板采用插入式连接方式,简单,合理,牢固,可靠。具有安装周期短、刚性好、防火效果好、隔音效果好等特点,具有广阔的应用前景。下面我们来了解一下怎么用岩棉复合板进行隔断吧!
Rock wool composite board adopts plug-in connection, which is simple, reasonable, firm and reliable. It has the characteristics of short installation cycle, good rigidity, good fire prevention effect and sound insulation effect, and has broad application prospects. Now let's learn how to partition with rock wool composite board!
根据工厂设置的建筑物测量图定位方格参考点,使用全站仪拉电线和直尺确定地面参考线(隔墙的线)。然后在基准线左侧100mm处释放板材地面施工基准线。根据地面施工基线,使用自动安平红外激光释放墙和网格底部的施工基线。使用全站仪重新检查地面、墙壁和网格结构的基线,垂直偏差不应超过±2mm。
Locate the grid reference point according to the building survey drawing set by the factory, and use the total station to pull the wire and ruler to determine the ground reference line (the center line of the partition wall). Then release the plate ground construction datum line at 100mm to the left of the datum line. According to the ground construction baseline, the construction baseline at the bottom of the wall and grid is released by automatic leveling infrared laser. Recheck the baseline of ground, wall and grid structure with total station, and the vertical deviation shall not exceed ± 2mm.
(1)固定底部定位片:根据地面施工基准安装墙壁的底部定位片(镀锌U形槽)。根据平面尺寸固定镀锌定位件。定位片的安装要求水平,并且用平板调整不平度。调整好定位部件并使其水平后,即可用内部膨胀螺栓将其固定。根据网格建设基准,安装与墙板相对应的顶部二级结构定位(L型镀锌角钢),固定点间距为300mm。
(1) Fixing the bottom positioning piece: install the bottom positioning piece (Galvanized U-groove) of the wall according to the ground construction standard. Fix the galvanized positioning parts according to the plane dimensions. The positioning piece shall be installed horizontally, and the unevenness shall be adjusted with a flat plate. After the positioning parts are adjusted and leveled, they can be fixed with internal expansion bolts. According to the grid construction benchmark, install the top secondary structure positioning (L-shaped galvanized angle steel) corresponding to the wallboard, and the spacing of fixing points is 300mm.
(2)与岩棉复合板的装配图进行比较,检查现场安装尺寸,长、宽之间是否有冲突,高度是否有空间。
(2) Compare with the assembly drawing of rock wool composite board to check whether there is conflict between length and width and whether there is space for height.
岩棉复合板.png
Rock wool composite board.png
(3)安装启动板并进行调整:将启动板的底部(侧面)固定在U形凹槽中,然后使用自动剪刀移动式升降机将启动板的另一端提升至垂直位置。然后使用自攻钉固定墙面板的相同二级结构(L型角钢)。
(3) Install and adjust the starting plate: fix the bottom (side) of the starting plate in the U-shaped groove, and then use the automatic scissors mobile elevator to lift the other end of the starting plate to the vertical position. Then fix the same secondary structure (L-angle steel) of the wall panel with self tapping screws.
(4)每次安装5个外墙面板时,必须测量和调整安装垂直度和直线度误差。
(4) When 5 exterior wall panels are installed each time, the installation perpendicularity and straightness errors must be measured and adjusted.
(5)完成岩棉板隔墙和原主体表面的安装后,在主体表面之间的缝隙中填入岩棉芯材,然后用L形镶边板覆盖缝隙,一侧固定在岩棉板上。一侧插入岩棉板和主墙之间的缝隙中,然后粘贴到主墙上。
(5) After the installation of rock wool board partition wall and the original main body surface, fill the gap between the main body surface with rock wool core material, then cover the gap with L-shaped edging board, and fix one side on the rock wool board. Insert one side into the gap between the rock wool board and the main wall, and then paste it to the main wall.
(6)收边板和室内装饰结构:在安装装饰条和彩色钢型材时,首先使用自动安平红外激光放置定位点,然后使用自攻边钉安装和固定,并注意它们的坚固和美观。
(6) Edge closing plate and interior decoration structure: when installing decorative strips and color steel profiles, first use automatic flat infrared laser to place positioning points, then use self tapping edge nails to install and fix them, and pay attention to their firmness and beauty.
(7)门窗开孔加固安装:用3mm厚的镀锌钢板加固开孔,然后安装门窗,用磨边装饰开孔。
(7) Reinforcement and installation of door and window openings: reinforce the openings with 3mm thick galvanized steel plate, then install doors and windows, and decorate the openings with edging.
(8)精加工:撕下保护膜并清洁板。
(8) Finishing: remove the protective film and clean the plate.
此文关键词: 济南复合板厂  

推荐阅读/ Recommended reading

C型钢怎么加工 [2018-08-23]

C型钢经热卷板冷弯加工而成,壁薄自重轻,截面性能优良,强度高,与传统槽钢相比,同等强度可节约材料。C-section steel is processed

岩棉夹芯板的优势在哪? 2021-11-11
济南复合板厂是如何进行复合板安装的? 2021-11-08
济南C型钢的简单介绍 2021-11-01
钛钢复合板的防治办法 2021-10-27