如今建筑彩钢板行业得到了显著的发展，各种各样的济南彩钢板出现在市场上，但是对于消费者来说这些彩钢板看得眼花缭乱，用的手忙脚乱，那么今天给大家讲解的问题是彩钢板安装的工艺要求。

Nowadays, the construction color steel plate industry has achieved remarkable development. A variety of Jinan color steel plates have appeared on the market, but for consumers, these color steel plates are dazzling and used in a hurry. So today, I will explain to you the process requirements for color steel plate installation.

1、槽铝固定：在固定铝之前，需要进行放线和定位。偏差不得超过5毫米，铝用M5x30抽芯铝拉钉固定，间接长度不超过300毫米，在有门洞的位置需要设置双拉钉，间距不超过50毫米

1. Fixing of aluminum groove: setting out and positioning are required before fixing aluminum. The deviation shall not exceed 5 mm. The aluminum shall be fixed with M5x30 core pulling aluminum rivet, and the indirect length shall not exceed 300 mm. Double rivet shall be set at the position with door opening, and the spacing shall not exceed 50 mm

2、T型吊梁固定：固定吊码应沿放线位置定位，间距不大于1.20米。将T型梁固定在连接济南彩钢板上时，需要用角铝或角铁压紧，不得留有间隙。压制的固体需要在两个彩色钢板的连接接缝上

2. Fixation of T-shaped lifting beam: the fixed lifting weights shall be positioned along the setting out position, with the spacing not greater than 1.20m. When fixing the T-shaped beam on the connecting Jinan color steel plate, it needs to be compressed with angle aluminum or angle iron, and no gap is allowed. The pressed solid needs to be on the joint of two color steel plates

3、风口安装：风口在天花板上的安装应按照图纸进行，避免“T”形梁。墙上的排气口和回风口应安装在离地面200毫米的地方。

3. Air vent installation: The air vent shall be installed on the ceiling in accordance with the drawings to avoid "T" beam. The air outlet and return air outlet on the wall shall be installed 200 mm above the ground.

4、外观要求：整体安装应平直美观，无碰撞和擦伤痕迹。保护膜不得在以后撕开。接缝应以水平方式连接，间距为3-4毫米。胶水应涂在所有接缝上，且应平直无缝隙。

4. Appearance requirements: the overall installation shall be straight and beautiful without collision and scratch marks. The protective film must not be torn off later. The joints shall be connected in a horizontal manner with a spacing of 3-4 mm. Glue shall be applied to all joints and shall be straight without gaps.

5、每个顶部和固定板需要用3个钻尾螺钉固定。固定板和立板之间的接缝需要用拉钉上下固定。施工过程中，接缝需要垂直。

5. Each top and fixed plate needs to be fixed with 3 drilling screws. The joint between the fixed plate and the vertical plate shall be fixed up and down with pull nails. During construction, the joints need to be vertical.

6、门窗安装：门窗的安装位置和开启方向应根据图纸要求确定。单扇门应尽可能在同一块彩钢板上，双扇门的中线应尽可能在板缝处，以便切割后的彩钢板可用作门板。门窗型材应连接紧密，无缝隙，整个门圈的留设尺寸应统一。

6. Installation of doors and windows: the installation position and opening direction of doors and windows shall be determined according to the drawing requirements. Single door shall be on the same color steel plate as far as possible, and the center line of double door shall be on the plate joint as far as possible, so that the color steel plate after cutting can be used as the door plate. Door and window profiles shall be closely connected without gaps, and the reserved size of the entire door ring shall be uniform.

7、内外弧固定：与彩钢板的连接需要密封，外弧柱不连接，内弧连接点位置良好，缝隙密封。

7. Fixation of inner and outer arcs: the connection with the color steel plate needs to be sealed, the outer arc column is not connected, the inner arc connection point is in good position, and the gap is sealed.

上文中的内容就是济南彩钢板安装的工艺要求了，希望能够对大家有所帮助。如果大家想要了解更多的关于彩钢板的知识，欢迎关注我们的网站http://www.jnjgcg.com动态。

The above content is the process requirements for the installation of Jinan color steel plate, and I hope it can help you. If you want to know more about color steel plate, please follow our website http://www.jnjgcg.com Dynamic.