Different users have different requirements for section steel wall thickness. If we want to meet these requirements at the same time, the production process and equipment of Jinan C-steel plant is very important. In general, it is difficult to produce high quality C-section steel by cold rolling, so C-section mill is used to complete.

　　物料从C型钢尾部进入后，被各种滚轮压下，由机头输出异形c梁。这不仅大大优化了必要的生产工艺，而且增加了产量。保证了c型钢产品壁厚均匀，界面形状复杂。

　　After the material enters from the tail of C-shaped steel, it is pressed down by various rollers, and the head outputs the special-shaped C-beam. This not only greatly optimizes the necessary production process, but also increases the output. The uniform wall thickness and complex interface shape of C-steel products are ensured.

　　为了达到精确的壁厚，c梁压力机所使用的模具由精确的上模具和一些相同尺寸、规格、尺寸的下模具组成。为了在加工前安装到位，不仅要保证上、下模具的平稳运行，还要保证上、下模具周围的间隙均匀，使压制的c型钢具有均匀的壁厚。

　　In order to achieve accurate wall thickness, the mold used in the C-beam press consists of accurate upper mold and some lower mold of the same size, specification and size. In order to be installed in place before processing, it is necessary to ensure not only the smooth operation of the upper and lower dies, but also the uniform gap around the upper and lower dies, so that the pressed C-section steel has a uniform wall thickness.

　　在加工C型钢的过程中，进行了模具的安装和主机的调试。然后启动空压机、真空泵、挤出机、切砖机、给料机、压砖机、主机和输送瓦机。停止时，停止挤出机，然后停止其余设备。

　　In the process of processing C-section steel, the installation of the die and the debugging of the main machine are carried out. Then start the air compressor, vacuum pump, extruder, brick cutter, feeder, brick press, main machine and tile conveyor. When stopping, stop the extruder first and then the rest of the equipment.

　　在使用设备前，我们要检查连接是否牢固，安装螺栓和螺母是否拧紧，并在左右底盘上加足润滑油后才能启动发动机电试。挤出机的泥浆由切料机切成固定长度，由滚筒输送机输送到压砖机，再由装载机按照规定程序输送到下模。将c型钢压坯在工作台上分好后，由卸砖机的真空吸盘吸附。分度后，放置在输送线的空白支架上。

　　Before using the equipment, we should check whether the connection is firm, whether the mounting bolts and nuts are tightened, and add enough lubricating oil to the left and right chassis before starting the engine electric test. The slurry of the extruder is cut into fixed length by the cutter, transported to the brick press by the roller conveyor, and then transported to the lower die by the loader according to the specified procedure. After the C-steel blank is divided on the workbench, it is absorbed by the vacuum suction cup of the brick unloader. After graduation, it is placed on the blank bracket of the conveyor line.

　　该机构制作的c梁壁厚可以很薄，大大简化了生产过程，提高了生产效率。可生产普通热轧方法难以生产的各种平均壁厚、复杂型材和不同材料的冷弯彩钢设备。

　　The thickness of the C-beam made by the mechanism can be very thin, which greatly simplifies the production process and improves the production efficiency. It can produce all kinds of cold-formed color steel equipment with average wall thickness, complex sections and different materials which are difficult to be produced by common hot rolling method.

　　以上是济南C型钢厂小编为大家介绍的相关内容，想要了解更多内容，欢迎访问网站：http://www.jnjgcg.com

　　The above is the relevant content introduced by the small edition of Jinan C steel works. If you want to know more, please visit the website: http://www.jnjgcg.com