The characteristics of color steel plate and the installation mode of color steel plate are mainly explained from the following aspects, hoping to help you.

A.）彩钢板均可拆卸再复原，可方便进行组装拆卸，标准单元墙板均可互换，对维护水电，线路改造等非常便捷。

A. ) the color steel plate can be disassembled and restored, which is convenient for assembly and disassembly. The standard unit wall panels can be interchanged, which is very convenient for maintenance, water and electricity, line transformation, etc.

河南彩钢板厂家

Henan color steel plate manufacturer

B）彩钢板板面可以任意开孔，对安装控制开关、电源插座等装置非常方便，不需另外处理。

B) The color steel plate surface can be perforated arbitrarily, which is very convenient for installing control switches, power sockets and other devices without additional treatment.

C）彩钢板表面颜色柔和，与地板、天花构成统一和谐的整体，使整个空间具有现代气息。

C) The surface color of the color steel plate is soft, forming a unified and harmonious whole with the floor and ceiling, making the whole space modern.

D）采用静电烤漆喷涂工艺，表面平滑、细腻，不积尘，保养简单， 了机房的洁净度要求。

D) The electrostatic baking paint spraying process is adopted, with smooth and fine surface, no dust accumulation and simple maintenance, which meets the cleanliness requirements of the machine room.

E）彩钢板符合国标A级防火标准，能充分满足机房建设装修的防火要求。

E) The color steel plate meets the class a fire protection standard of the national standard and can fully meet the fire protection requirements for the construction and decoration of the machine room.

彩钢板的安装方式

Installation method of color steel plate

1）放样：依图面及现场实测尺寸进行放样（隔墙中 心线）以两收边中 心线与地面的交点弹出地轨中 心线。应 这四条线处在一个垂直面内，以 以后安装之墙面的垂直。

1) Setting out: setting out shall be carried out according to the drawing surface and on-site measured dimensions (partition center line), and the ground rail center line shall be snapped at the intersection of the two trimming center lines and the ground. These four lines shall be in a vertical plane to ensure the perpendicularity of the wall to be installed later.

2）天轨：安装要整齐，接口处须补强修齐，每隔500mm—600mm击钉或螺丝固定于水泥天花板。

2) Overhead rail: the installation shall be neat, the interface shall be reinforced and repaired, and fixed on the cement ceiling with screws or screws every 500mm-600mm.

3）地轨：安装地轨时要先把门的安装位置预留，尚需注意地差问题。如地面高低差太多，须整平使其落差减少，不影响调整水平，每隔600mm以击打或螺丝固定地坪上，如果地缝太大以填缝剂补满。

3) Ground rail: when installing the ground rail, reserve the installation position of the door first, and pay attention to the ground difference. If the ground height difference is too large, it shall be leveled to reduce the drop without affecting the adjustment level. It shall be fixed on the floor with blows or screws every 600mm. If the ground joint is too large, it shall be filled with joint sealant.

4）收边：根据实际测量值切割收边，切割后边缘修齐。力求整齐一致，连接处要求无缝隙。与天及踢脚板接口处尤其注意，更要做到无缝隙。

4) Edge trimming: cut the edge trimming according to the actual measured value, and trim the edge after cutting. Strive to be neat and consistent, and the joints shall be free of gaps. Pay special attention to the interface with the ceiling and skirting board, and make sure there is no gap.

5） 竖向龙骨：每隔49cm置一支竖向龙骨（为隔板尺寸的一半）,门框两侧立柱上下完全固定，不致于摇晃，反方向增加一支竖向龙骨，门扇宽度超过90cm以上，门框上横立柱须加强固定，必要时以焊接固定之。

5) Vertical keel: set a vertical keel every 49cm (half the size of the partition). The columns on both sides of the door frame are completely fixed up and down without shaking. Add a vertical keel in the opposite direction. The width of the door leaf exceeds 90cm. The horizontal columns on the door frame must be strengthened and fixed by welding if necessary.

河南彩钢板厂家

Henan color steel plate manufacturer

6）横向穿心龙骨：高超过3米以上，以垂直方向1.2米置一支，当连两支衔接处须重叠，重叠长度不得少于10cm。

6) Transverse through keel: if the height is more than 3m, one keel shall be set at 1.2m in the vertical direction. When the two branches are connected, they must be overlapped, and the overlapping length shall not be less than 10cm.

7）墙板：由一侧开始安装彩钢板，依次安装，相连板间距12mm。隔板之间采用宽度12mm压条，标准单元墙板均可互换。

7) Wallboard: color steel plates shall be installed from one side in sequence, and the spacing between connected plates shall be 12mm. 12mm wide battens are used between diaphragms, and standard unit wallboards can be interchanged.

安装注意事项：板之间采用宽度12mm的压条，标准单元墙板均可互换，在安装墙板时更要注意细节，将墙板用托板车运安装点附近，再使用吸盘将金属 板直立，使其下端靠在踢脚板上，衬板两侧紧靠竖向龙骨，单边与另一片墙板间距12mm，用固定件靠上，再把自攻螺丝固定于竖向龙骨上，固定间距在300mm—400mm之间，组装时须注意水平及垂直，当到后一块墙板时，如须裁切时，须丈量过尺寸后，再按正确方式裁切修齐，将其安装于墙面上。

Precautions for installation: 12mm wide battens are used between the panels, and the standard unit wall panels can be interchanged. Pay more attention to the details when installing the wall panels. First, transport the wall panels to the vicinity of the installation point with a pallet truck, and then use a suction cup to stand the metal plates upright, so that the lower end rests against the skirting plate, the two sides of the lining plate are close to the vertical keel, the spacing between one side and another wall panel is 12mm, and use a fixing piece to lean against it, Then fix the self tapping screws on the vertical keel with a fixed spacing of 300mm-400mm. Pay attention to the horizontal and vertical during assembly. When the latter wall panel needs to be cut, if it needs to be cut, measure the size, cut and trim it in the correct way, and install it on the wall.

本文的精彩内容由济南彩钢板为您提供，本网站还有很多的精彩内容，更多的内容您可以点击进入：http://www.jnjgcg.com我们有专门的客服为您解答问

The wonderful contents of this article are provided by Jinan color steel plate. There are many wonderful contents on this website. You can click to enter more contents: http://www.jnjgcg.com We have special customer service to answer your questions